F911A227KNCAJ6 [KYOCERA AVX]

Automotive Low ESR Tantalum Capacitor;


型号：	F911A227KNCAJ6
厂家：	KYOCERA AVX
描述：	Automotive Low ESR Tantalum Capacitor
文件：	总3页 (文件大小：597K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

F91-AJ6 Series – Automotive Product Range

F91-AJ6 Series

Low ESR, Resin-Molded Chip - Automotive Product Range

FEATURES

•

Compliant to the RoHS3 directive 2015/863/EU

Compliant to AEC-Q200

100% Surge Current Tested

LEAD-FREE COMPATIBLE

COMPONENT

APPLICATIONS

•

Cabin Electronics

Infotainment

CASE DIMENSIONS: millimeters (inches)

EIA

L ± 0.20

(0.008)

W ± 0.20 (0.008) H ± 0.20 (0.008)

W₁± 0.20

(0.008)

1.20 (0.047)

2.20 (0.087)

2.40 (0.094)

A ± 0.30 (0.012)

-0.20 (0.008)

0.80 (0.031)

1.30 (0.051)

Code EIA Code

S Min.

Metric

-0.10 (0.004)

1.60 (0.063)

2.80 (0.110)

4.30 (0.169)

-0.10 (0.004)

1.60 (0.063)

1.90 (0.075)

2.90 (0.114)

1206

1210

2917

3216-18

3528-21

7343-31

3.20 (0.126)

3.50 (0.138)

7.30 (0.287)

1.10 (0.043)

1.40 (0.055)

4.40 (0.173)

W₁dimension applies to the termination width for a dimensional area only

A, B, N CASE

Capacitance Value in pF

476 = 47μF

AVX LOGO

Rated Voltage Code

A = 10V

ID Code

Polarity

Band

(Anode+)

476 A

xxxxx

16V

20V

25V

35V

6.3V

10V

*Capacitance code of “P” case products are as shown below.

HOW TO ORDER

AJ6

F91

226



Type

Rated

Voltage

Capacitance Code

pF code: 1st two

digits represent

Tolerance

K = ±10%

M = ±20%

Case

Size

Packaging

Tolerance

K = ±10%

M = ±20%

See Tape & Reel

Packaging Section

See

signiﬁcant ﬁgures,

3rd digit represents

multiplier (number of

zeros to follow)

table

above

TECHNICAL SPECIFICATIONS

Category Temperature Range

Rated Temperature

Capacitance Tolerance

Dissipation Factor

-55 to +125°C

+85°C

±20%, ±10% at 120Hz

Refer to next page

ESR 100kHz

After 1 minute’s application of rated voltage, leakage current at 20°C is not

more than 0.01CV or 0.5μA, whichever is greater.

After 1 minute’s application of rated voltage, leakage current at 85°C is not

more than 0.1CV or 5μA, whichever is greater.

After 1 minute’s application of derated voltage, leakage current at 125°C is not

more than 0.125CV or 6.3μA, whichever is greater.

+15% Max. at +125°C

Leakage Current

Capacitance Change By Temperature

+10% Max. at +85°C

-10% Max. at -55°C

The Important Information/Disclaimer is incorporated in the catalog where these speciﬁcations came from or

available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.

090121

F91-AJ6 Series

Low ESR, Resin-Molded Chip - Automotive Product Range

CAPACITANCE AND RATED VOLTAGE RANGE

(LETTER DENOTES CASE SIZE)

Capacitance

Rated Voltage

10V (1A)

*1: ΔC/C Marked “*”

Item

Damp Heat

Temperature cycles

Resistance soldering heat

Surge

μF

Code

6.3V (0J)

16V (1C)

106

226

336

476

107

227

All Case (%)

±10

A,B

100

220

Endurance

Released ratings

RATINGS & PART NUMBER REFERENCE

Rated

ESR

100kHz RMS Current (mA)

ΔC/C

(%)

AVX

Capacitance

Case Size

Voltage

(V)

DCL (μA)

@ 120Hz @ 100kHz

MSL

Part No.

(μF)

(%)

(mΩ)

25ºC

85ºC

125ºC

6.3 Volt

F910J226#AAAJ6

F910J476#AAAJ6

F910J476#BAAJ6

F910J107#BAAJ6

6.3

1.4

3.0

6.3

1250

500

245

412

435

220

371

391

165

174

100

450

10 Volt

F911A106#AAAJ6

F911A226#AAAJ6

F911A336#BAAJ6

F911A476#BAAJ6

F911A227#NCAJ6

1.0

2.2

1500

1250

700

224

245

348

412

1225

201

220

314

371

1102

139

165

490

3.3

220

4.7

22.0

500

100

16 Volt

F911C106#AAAJ6

F911C226#BAAJ6

F911C336#BAAJ6

F911C107#NCAJ6

1.6

3.5

1500

950

100

224

299

201

269

120

490

5.3

299

269

100

16.0

1225

1102

#: "M" for ±20% tolerance, "K" for ± 10% tolerance.ꢀMoisture Sensitivity Level (MSL) is deﬁned according to J-STD-020.

QUALIFICATION TABLE

F91-AJ6 series (Temperature range -55ºC to +125ºC)

Condition

At 40°C, 90 to 95% R.H., 500 hours (No voltage applied)

TEST

Damp Heat

Capacitance Change .................. Refer to the table above (*1)

Dissipation Factor ....................... Initial speciﬁed value or less

Leakage Current .......................... Initial speciﬁed value or less

(Steady State)

Load Humidity

After 1000 hour’s application of rated voltage in series with a 33Ω resistor at 85°C, 85% R.H.,

capacitors meet the characteristics requirements table below.

Capacitance Change .................. Refer to the table above (*1)

Dissipation Factor ....................... Initial speciﬁed value or less

Leakage Current .......................... 125% or less than the initial speciﬁed value

At -55°C / +125°C, 30 minutes each, 1000 cycles

Capacitance Change .................. Refer to the table above (*1)

Dissipation Factor ....................... Initial speciﬁed value or less

Leakage Current .......................... Initial speciﬁed value or less

Temperature Cycles

10 seconds reﬂow at 260°C, 10 seconds immersion at 260°C.

Capacitance Change .................. Refer to the table above (*1)

Dissipation Factor ....................... Initial speciﬁed value or less

Leakage Current .......................... Initial speciﬁed value or less

Resistance to Soldering Heat

After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles

at 85ºC, capacitors shall meet the characteristic requirements in the table above.

Capacitance Change ....................Refer to the table above (*1)

Surge

Dissipation Factor .........................Initial speciﬁed value or less

Leakage Current ...........................Initial speciﬁed value or less

After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series with a 3Ω

resistor at 125°C, capacitors shall meet the characteristic requirements in the table above.

Capacitance Change ................ Refer to the table above (*1)

Endurance

Shear Test

Dissipation Factor..................... Initial speciﬁed value or less

Leakage Current ....................... Initial speciﬁed value or less

After applying the pressure load of 17.7N for 60 seconds horizontally to the center of capacitor side body which

has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its

sign at the terminal electrode.

Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the

opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a speciﬁed

jig at the center of the substrate so that substrate may bend by1mm as illustrated. Then, there shall be found no

remarkable abnormality on the capacitor terminals.

1% per 1000 hours at 85°C, V_Rwith 0.1Ω/V series impedance,

60% conﬁdence level.

Terminal Strength

Failure Rate

The Important Information/Disclaimer is incorporated in the catalog where these speciﬁcations came from or

available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.

040120

F91-AJ6 Series

Low ESR, Resin-Molded Chip - Automotive Product Range

AVX SOLID ELECTROLYTIC CAPACITOR ROADMAP

SERIES LINE UP : CONVENTIONAL SMD MnO₂

TMJ

ultra

low DCL

THH

230°C COTS+

Hermetic

High Rel.

& Special

THJ

F97-HT3

High Temp

200°C

175°C auto

135°C auto

TRM

professional

multianode

TRJ

F91-AJ6

F97

Industrial &

Automotive

professional

auto

professional

TAJ

TPS

F93-AJ6

F98-AJ6

auto

auto *T/*U

auto

TPM

TPS

F91

multianode

Standard

TAJ

F93

F92

Standard

Low Profile

TAJ

TAC

TPC

Low Proꢀle

microchip

Low ESR

F98-AS1

undertab,

fused

TLN

TLC

F98

High CV

TLJ

undertab

microchip

undertab

The Important Information/Disclaimer is incorporated in the catalog where these speciﬁcations came from or

available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.

030321

相关型号：